Search Results - Swedespeed
Username
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    Search:

    Type: Posts; User: uqj83l

    Page 1 of 3 1 2 3

    Search: Search took 0.02 seconds.

    1. Iíve never known the dust covers to rattle....

      Iíve never known the dust covers to rattle. Perhaps youíve lifted the car beyond what the shock parameters? If you drive over a hump in the road and get a knocking noise as the car recovers...
    2. Clip is one use only design.

      Clip is one use only design.
    3. Replies
      2
      Views
      168

      If you are going to attempt this yourself and you...

      If you are going to attempt this yourself and you havenít got the prop shaft holding tool, then use one of the exhaust rubbers wedged between the flange and the chassis. It grips in the gap perfectly...
    4. Replies
      2
      Views
      168

      Not seen this but if it is as you describe itíll...

      Not seen this but if it is as you describe itíll be tricky to do on the floor. You can buy a haldex seal kit if it is leaking haldex fluid. The big O ring is the one that seals the case to the rear...
    5. Replies
      2
      Views
      160

      How sure are you that itís transmission oil?

      How sure are you that itís transmission oil?
    6. Replies
      4
      Views
      327

      I had the opposite happen. I swapped in a 2005...

      I had the opposite happen. I swapped in a 2005 engine complete with a 2005 alternator into my 2004 car. The CEM threw a ďbattery not chargingĒ fault. I swapped in my 04 alternator onto the 05 block...
    7. Replies
      3
      Views
      186

      Brilliant. Thanks guys.

      Brilliant. Thanks guys.
    8. Replies
      3
      Views
      186

      Removing a programmed module from the CEM

      Hi, I have a 2004 VR and Iíve had to disconnect the ďin car phone moduleĒ by removing the green plug from the rear. It was interfering with the CFE and hence advised to disconnect. I donít use it...
    9. Replies
      8
      Views
      274

      Image?

      Image?
    10. Replies
      6
      Views
      270

      I donít think it does. It was over a year ago...

      I donít think it does. It was over a year ago when I did mine. Just to make sure when the car was remapped the solenoid setting was changed to permanently keep the EGR valve closed. No CEL.
    11. Replies
      6
      Views
      270

      Good write up. Welcome! If you get a chance...

      Good write up. Welcome!
      If you get a chance clean the intake pipe to the manifold and the Governor. Also consider a remap to 185 and blanking the EGR. Itíll run a lot nicer. Lots of write ups on...
    12. Can you get replacement internals for the M66C?

      Hi
      I have a 2004 VR and my 2nd gear synchros are worn resulting in gear crunch. Can new rings still be sourced for this transmission? If so, where?
      Thanks.
    13. Replies
      2
      Views
      226

      Thanks. Thatís really helpful. My collar sleeve...

      Thanks. Thatís really helpful. My collar sleeve was sliding forward and back between my transmission output shaft and angle gear.
      The reason I asked was because I saw an M66E AWD transmission where...
    14. Replies
      2
      Views
      226

      M66 collar sleeve quick question

      Hi
      I have a 2004 M66 and I noticed that there isnít an oil seal inside the collar sleeve when the angle gear has been removed. Is this correct? Only Iíve seen another 5 speed AWD setup where there...
    15. Replies
      6
      Views
      305

      Iíve lifted from the underbody just behind the...

      Iíve lifted from the underbody just behind the subframe mounts close to the vertical part of the underbody. It takes the weight of the front end here without any distortion.
    16. Replies
      1
      Views
      146

      Angle gear compatibility

      Hi. Quick question: can you replace an angle gear in a 2004 M66 with a replacement from a 2005 Geartronic with no issues?
      Thanks.
    17. Replies
      17
      Views
      1,009

      Try having the wheels roadforce balanced. This...

      Try having the wheels roadforce balanced. This cured my vibration after chasing many other components.
    18. Replies
      22
      Views
      1,048

      Maybe alternator?

      Maybe alternator?
    19. Also look at your EVAP system including checking...

      Also look at your EVAP system including checking if the purge valves are operating correctly.
    20. Replies
      9
      Views
      353

      I had a strange clunk like this, turns out it was...

      I had a strange clunk like this, turns out it was the 2 large bolts at each end of the upper engine stabiliser bar came loose. Always worth a quick check.
    21. Replies
      4
      Views
      291

      Mine definitely doesnít!

      Mine definitely doesnít!
    22. Replies
      4
      Views
      291

      I donít think these cars go into 5th gear with...

      I donít think these cars go into 5th gear with the car stationary and engine off.
    23. Final question. The shock in your image doesnít...

      Final question. The shock in your image doesnít look like a nivomat. My nivomats have a rubber boot reaching to the end. My XC is an AWD by the way. Not sure if thatís why.....
    24. And whatís the length of the elongated hex nut?...

      And whatís the length of the elongated hex nut? 20mm or 40mm?
    25. Great help thanks. I assume those bits are custom...

      Great help thanks. I assume those bits are custom and not part of the PU kit?
    26. 20mm PU lift kit on XC70 with nivomats on rear

      Hi
      Can anyone confirm if the 20mm lift kits with PU spacers can work on a 2005 XC70 which has nivomats on rear with no adverse affect?
    27. Replies
      132
      Views
      8,414

      Iím also thinking of a 20mm lift kit, but Iím...

      Iím also thinking of a 20mm lift kit, but Iím afraid it will force the geometry to positive camber. Does it do this, and is there any cure to the positive camber?
    28. Replies
      34
      Views
      1,375

      If your radiator cap has been replaced and youíve...

      If your radiator cap has been replaced and youíve got a lip on the upper radiator hose connection I can only suggest keeping the coolant level a fraction over minimum in the coolant tank rather than...
    29. Replies
      15
      Views
      854

      It doesnít look right at all. Do you have the...

      It doesnít look right at all. Do you have the washer under the spring seat?
    30. I also fitted brand new pads as the old ones had...

      I also fitted brand new pads as the old ones had worn a fraction more at one end than the other.
    Results 1 to 30 of 71
    Page 1 of 3 1 2 3